20 Gauge Vs 16 Gauge Piercing. The equivalent thicknesses differ for each gauge size standard. which were developed based on the weight of the sheet for a given material. This means the thickness of the portion that goes through the piercing is approximately.8 millimeters.
DIAMOND Cartilage. Tragus. Helix. Monroe. Nose Stud from bodyjewelryfactory.com
I was cool with this and wanted to give it a shot. partly because ive found some nice studs that are slightly big in my original piercings. and itd be cool to be able to wear them more easily in the new one. Nose piercings can come in several different sizes. too. Like other cartilage piercings. the daith is pierced with a 16 gauge needle. which is 1.2mm thick.
The higher the gauge. the thinner the barbell. The most common piercing size for a nose ring is an 18 or 20 gauge. which is equivalent to 1mm and 0.8mm. respectively.
This is especially the case if the initial jewelry placed is a flatback. 22 gauge (.6mm) piercings done in india. the middle east. or very select areas of the us. uk. australia. or europe may use the tiniest size:
For example. a 22g barbell is going to be very thin. and a 14g barbell is going to be thicker. The 1″ thickness of the steel was measured in diminishing fractions such as 1/14″ thick. 1/16″ thick. 1/20″ thick. and so on.
Few people know why the thickness of steel diminishes as the gauge increases (ie: If its too small and the 20 gauge moves around alot in the piercing then you are probably looking at an 18 or even 16 gauge.
So. an earring thats a 16 gauge is thicker than an earring thats a 20 gauge. My new piercing was done at a 16g. and my piercer told me that i can wear 18g or 20g jewelry in it after it heals. but that the hole will probably shrink a bit if i do.
For example. aside from the standard gauge sizes. it can also come in. If it fits perfectly then your piercing is a 20 gauge.
If It Fits Perfectly Then Your Piercing Is A 20 Gauge.
The smallest gauge available for body jewelry is 20. while the largest is 0000. after which gauges are measured in fractions of an inch. For larger gauges—like stretched ear lobes—the smallest gauge usually starts at size 8 and goes up from there. This is especially the case if the initial jewelry placed is a flatback.
My New Piercing Was Done At A 16G. And My Piercer Told Me That I Can Wear 18G Or 20G Jewelry In It After It Heals. But That The Hole Will Probably Shrink A Bit If I Do.
Gague are used to specify the thickness of a metal sheet. The 20 gauge correlates to 0.8 millimeters of the thickness of the piercing piece that will go through your nose. It will be fine. but your ears may close around them making it hard to wear 16g earrings if you leave them in for a long time (just like it will be hard to wear 16g earrings if you dont wear earrings for a long time).
Alternatively. If Your Goal Is To Stretch Your Earlobes. You Will Likely Start With A 14 Gauge Piercing And Work To Gradually Increase.
If its too big you may need to go down to a 22 gauge. If. however. you’ve been wearing earrings with thinner posts in your daith. you may want to try earrings with slightly thinner 18 gauge posts (1.0mm thick). In other words. it’s the barbell’s thickness.
18G. 16G. 14G And 12G Are All Fairly Standard Gauges For Ear Piercings.
For example. a 22g barbell is going to be very thin. and a 14g barbell is going to be thicker. Few people know why the thickness of steel diminishes as the gauge increases (ie: So a 12 gauge barbell is much thicker than a 20 gauge barbell.
The Smallest Gauge Is Typically Considered Something Along The Lines Of A 22 Gauge. Which Is Very Tiny.
Standard ear wires are 20 gauge. Like other cartilage piercings. the daith is pierced with a 16 gauge needle. which is 1.2mm thick. For ear piercings. this measurement is a little different.